A three-dimensional coordinate measuring method based on ultrasonic sensor

SHAN Liang1; KONG Ming2; HOU Rui2; ZHAO Jun2

doi:10.13873/j.1000-97872013.06.043

Chinese

您当前的位置：

首页 >

文章列表页 >

A three-dimensional coordinate measuring method based on ultrasonic sensor

更新时间：2025-09-11

- A three-dimensional coordinate measuring method based on ultrasonic sensor
- Vol. 32, Issue 6, Pages: 123-125(2013)
- 作者机构：
  
  1. 中国计量学院信息工程学院
  2. 中国计量学院计量测试工程学院
- 作者简介：
- 基金信息：
- DOI：10.13873/j.1000-97872013.06.043
  CLC： TP274
- Published：2013
- 稿件说明：
移动端阅览
[1]单良,孔明,侯蕊,赵军.一种基于超声传感器的三维坐标测量方法[J].传感器与微系统,2013,32(06):123-125.

SHAN Liang1, KONG Ming2, HOU Rui2, et al. A three-dimensional coordinate measuring method based on ultrasonic sensor[J]. 2013, 32(6): 123-125.
[1]单良,孔明,侯蕊,赵军.一种基于超声传感器的三维坐标测量方法[J].传感器与微系统,2013,32(06):123-125. DOI： 10.13873/j.1000-97872013.06.043.

SHAN Liang1, KONG Ming2, HOU Rui2, et al. A three-dimensional coordinate measuring method based on ultrasonic sensor[J]. 2013, 32(6): 123-125. DOI： 10.13873/j.1000-97872013.06.043.

摘要

提出一种基于超声传感器的低成本三维测量方法。该方法采用一个超声波发射端和多个超声波接收端的组合

通过超声测距原理获得发射端到多个接收端的距离

从而计算超声波接收端的空间三维位置;在超声波三维测量方法的基础上

推导了基于最小二乘法的三维位置反演算法

搭建了基于FPGA的测量硬件系统并进行了实验研究。实验结果表明:坐标估计的绝对误差小于20 mm

重复性较好

测量精度有进一步提高的空间。

Abstract

A low-cost three-dimensional coordinate measuring method based on ultrasonic sensors is proposed.One ultrasonic wave transmitting terminal and multiple ultrasonic wave receiving terminal are used in this method.The distances between transmitting and receiving terminal are calculated by the principle of ultrasonic ranging

then spatial three-dimensional coordinates of receiving terminal are calculated.On the basis of ultrasonic wave three-dimensional measurement method

three-dimensional position inversion algorithm based on least-square method is derived and measuring system based on FPGA is set up and experimental research is carried out.The experimental results indicate that the absolute error of coordinate estimation is less than 20 mm with good repeatability and measuring precision can be improved further.

关键词

Keywords

references

基于激光跟踪仪的数控机床几何误差辨识方法 [J]. 王金栋,郭俊杰,费致根,邓玉芬. 机械工程学报 . 2011(14)

陀螺经纬仪在地理空间定向中的应用研究——以西安地铁工程为例 [J]. 姜雁飞,胡荣明,杨联安. 西北大学学报(自然科学版) . 2011(01)

GPS在三峡库区开县大榜8社滑坡监测中的应用 [J]. 王刚,杨强,李强. 山西建筑 . 2011(02)

飞机翼面类部件柔性装配五坐标自动制孔设备的研制 [J]. 周万勇,邹方,薛贵军,甘露,杜宝瑞. 航空制造技术 . 2010(02)

点阵式测头成像视觉三坐标测量系统建模 [J]. 张雪飞,彭凯,刘书桂. 制造技术与机床 . 2007(03)

新型纳米级二维共平面工作台的参数测试 [J]. 王伟丽,范光照. 机械制造 . 2006(02)

三坐标测量技术在汽车制造业中的应用 [J]. 王昊. 现代制造工程 . 2005(07)

工业测量系统最新进展及应用 [J]. 李广云. 测绘工程 . 2001(02)

Views

173

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Underwater acoustic sensing control system of micro-ring resonant cavity based on FPGA

Design and implementation of π/8-D8PSK soft demodulation system based on probabilistic calculation

Design of PZT-based 500 MHz ultrasonic sensor and MEMS fabrication

Gesture recognition system based on single vibration element ultrasonic sensor

High speed tracking of muitilight-emitting targets

Related Author

WU Bofeng

YANG Yuhua

CHU Xiaoxia

ZHANG Guojun

ZHANG Wendong

CUI Jiangong

PANG Yu

ZHANG Yang

Related Institution

State Key Laboratory of Dynamic Measurement Technology,North University of China

Photoelectronic Information Sensing and Transmission Technology Laboratory,Chongqing University of Posts and Telecommunications

Center National De Recherche Scientifique,Institut of Electronics,Microelectronics and Nanotechnology,UMR 8520,Department of Opto-Acousto-Electronics at University of Valenciennes and Hainault Cambresis

State Key Laboratory of ASIC and System,School of Microelectronics,Fudan University

State Key Laboratory of Mechanical System and Vibration,Shanghai Jiao Tong University

⁰