Cantilever beam deflection correction method for coating layer thickness measurement

ZHANG Shuai; JIN Yong; WANG Zhao-ba

doi:10.13873/j.1000-9787(2018)11-0058-02

Chinese

您当前的位置：

首页 >

文章列表页 >

Cantilever beam deflection correction method for coating layer thickness measurement

更新时间：2025-09-11

- Cantilever beam deflection correction method for coating layer thickness measurement
- Vol. 37, Issue 11, Pages: 58-59+62(2018)
- 作者机构：
  
  中北大学信息与通信工程学院
- 作者简介：
- 基金信息：
- DOI：10.13873/j.1000-9787(2018)11-0058-02
  CLC： TP391.41
- Published：2018
- 稿件说明：
移动端阅览
[1]张帅,金永,王召巴.包覆层厚度测量的悬臂梁挠度校正方法[J].传感器与微系统,2018,37(11):58-59+62.

ZHANG Shuai, JIN Yong, WANG Zhao-ba. Cantilever beam deflection correction method for coating layer thickness measurement[J]. 2018, 37(11): 58-59+62.
[1]张帅,金永,王召巴.包覆层厚度测量的悬臂梁挠度校正方法[J].传感器与微系统,2018,37(11):58-59+62. DOI： 10.13873/j.1000-9787(2018)11-0058-02.

ZHANG Shuai, JIN Yong, WANG Zhao-ba. Cantilever beam deflection correction method for coating layer thickness measurement[J]. 2018, 37(11): 58-59+62. DOI： 10.13873/j.1000-9787(2018)11-0058-02.

摘要

测量较长的固体火箭发动机包覆层的厚度时

悬臂梁的挠度会增大

导致厚度的测量精度达不到0.05 mm的要求。为了校正悬臂梁的挠度

提出一种基于机器视觉的悬臂梁挠度检测方法。在悬臂梁支架上安装一点激光器

另一端安装一个反射板。采用电荷耦合器件（CCD）相机采集反射板上的激光点

对光电图像进行处理

计算出光点中心坐标

根据不同位置的光点坐标值

修正两次测量的挠度误差。实验验证:提出的误差最大不超过0.03 mm

测量厚度的精度满足0.05 mm。

Abstract

When measuring the thickness of the coating layer of long solid rocket engine

the deflection of the cantilever beam will increase

which results in measurement precision of the thickness can not reach requirement of0.05 mm.In order to correct the deflection of the cantilever beam

a method for detecting the deflection of cantilever beam based on machine vision is proposed.A point laser is installed on the cantilever beam support

a reflector is installed on the other end. The charge coupled device（CCD） camera is used to collect the laser points on the reflector.The photoelectric image is processed and the center coordinates of the light point are calculated. The deflection errors of the two measurements are corrected according to the coordinates of the light points in different positions.The method is verified by experiments.The maximum error is not more than 0.03 mm

and the precision of thickness measurement meets the requirement of 0.05 mm.

关键词

Keywords

references

基于单目视觉的桥梁挠度检测系统的研究 [J]. 胡晓,李鹏飞,朱旭东,刘荣钢. 电子技术与软件工程 . 2016(13)

双边非局部均值滤波图像去噪算法 [J]. 韩震,王红斌,余正涛,朱映柔. 传感器与微系统 . 2016(06)

基于图像传感器的铁轨表面缺陷视觉检测算法 [J]. 茅正冲,邬锋. 传感器与微系统 . 2015(09)

面向大尺寸检测CCD图像中心提取精度的研究 [J]. 林润芝,杨学友,邹剑,邾继贵,吴斌. 传感器与微系统 . 2010(12)

基于激光和视频的桥梁挠度测量新系统 [J]. 蓝章礼,张洪,周建庭. 仪器仪表学报 . 2009(11)

几种激光光斑中心定位算法的比较 [J]. 唐冠群. 北京机械工业学院学报 . 2009(01)

一种改进的小波软阈值去噪方法性能分析[J]. 刘卫东,刘尚合,王雷,胡小锋. 军械工程学院学报. 2007 (03)

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on piezoelectric energy harvesting technology of wireless sensor networks

Micro-nano displacement measurement system based on optical lever

Modeling and simulation of bimorph cantilever piezoelectric energy harvester

Finite element analysis of thermal structure composite film based on ABAQUS

Electrical performance analysis of piezoelectric fiber composites cantilever

Related Author

CHEN Nannan

ZOU Lijun

WU Xiaodong

MA Tianbing

XIU Qiang

LI Lu-lu

MA Shu-jun

ZHANG Chong

Related Institution

Institute of Mechanical Engineering,Anhui University of Science and Technology

School of Mechanical Engineering & Automation,Northeastern University

School of Electrical Engineering and Automation, Henan Polytechnic University

School of Mechanical Engineering, Jiangsu University

School of Mechanical and Electrical Engineering,Harbin Institute of Technology

⁰